Smart lightraise manual. SMART LIGHTRAISE 60WI USER MANUAL Pdf Download. 2019-03-14

Smart lightraise manual Rating: 8,7/10 1953 reviews

SMART LIGHTRAISE 40WI QUICK REFERENCE MANUAL Pdf Download.

smart lightraise manual

You might have single touch only, depending on your operating system. I M P O R T A N T The overall finger touch performance is strongly influenced by the projection surface flatness. C A U T I O N Do not reset the lamp hours unless you have just replaced the lamp module. Performing initial troubleshooting on your projector will reduce the time of a support call. You may not see an image for up to 60 seconds because the projector needs to warm its lamp. The default is On -20 dB.

Next

Smart Technologies Lightrise 40wi User Manual

smart lightraise manual

Confirm off Confirm off is a non-selectable power state that is returned during stage one of the two-button Off sequence. If the projector is on and its status light displays solid green, press the Power button twice on the remote control to put the projector into Standby mode. Turn on the interactive pen. Idle The projector is off but still receiving power Standby mode. Select a dry-erase board with no bezel or with a bezel thickness of less than 3 mm above the board surface. Keep this setting on if your microphone is too sensitive. Write over an open file, folder or website with the interactive pen.

Next

Important information

smart lightraise manual

Microphone Turns the microphone input jack On The default is On. Partial, scrolling or incorrectly displayed image. Laptops may require a keyboard short-cut to initiate video out. Use the table below to determine the status of the projector. The projector scales the image to fit one of the following aspect ratios: Fill: The full size of the projection area is used.

Next

Smart Technologies LightRaise Manuals and User Guides, Projector Accessories Manuals — All

smart lightraise manual

Command Command target range Response. Zooming in cuts off the outer edges of the source video. Do not attempt to replace the lamp. Command Command target range Response. You can adjust the length of the boom for different image sizes.

Next

Smart Technologies Lightrise 40wi User Manual

smart lightraise manual

Adjusting this setting can affect touch function. The projector Power and Service lights are off If the projector Power and Service lights are both off, one of the following issues is occurring: There was a power outage or a power surge. This procedure must be completed before you can use the interactive projector. Microphone Boost Boost is applied in the Off setting. Error states Solid No touch.

Next

Smart Technologies LightRaise 60wi Manuals and User Guides, Projector Manuals — All

smart lightraise manual

Connect all the cables to the projector and let them hang loose. You can switch between different media using the projector remote control. Hold down the side release on the left side of the battery holder and pull the battery holder completely out of the remote control. Adjust this setting only after you make all physical image adjustments. See the LightRaise 60wi interactive projector installation template smarttech. Keep the interactive pen and pen holder out of reach of small children as there are small parts that may pose a potential choking hazard. The Display Properties window appears.

Next

LightRaise 60wi/60wi2

smart lightraise manual

You can access these documents by visiting the LightRaise support page at smarttech. See Value-based command methods on page 82 for setting absolute and adjustment commands. Using this template ensures that you can do the following: Determine where to install the projector in relation to the studs in the wall and the size of the projection surface. Connect the projector power cable to the wall outlet, and then turn on the projector. W A R N I N G Measure the distance between the projector and the peripheral device you want to connect.

Next

Important information

smart lightraise manual

You can touch the screen to open files, navigate folders and manipulate content. Fill Screen, Match Input or 16:9. Economy increases the lamp life by decreasing the brightness of the image. All of the lines that you draw to install the interactive projector must be straight and level on a plumb wall. These commands are available when the projector is in Standby mode and when it is on. A specially filtered infra-red camera and signal processor, embedded in your interactive projector, can track up to two fingers or two pens simultaneously.

Next

Important information

smart lightraise manual

The serial number is on top of the projector in the location shown below: Accessing the service menu. The maximum allowable password length is four numbers or letters. Failure to do so can cause injuries including loss of eyesight if the lamp shatters or bursts. Number Control Function Power button Tap the Power button to turn the projector on and off. Each touch acts as a left-click. If the distance is less than 5 mm in all directions, optimal finger touch performance will likely be achieved. Select your troubleshooting issue from the list that appears, and then click Next.

Next

SMART LIGHTRAISE 40WI QUICK REFERENCE MANUAL Pdf Download.

smart lightraise manual

Choosing a height The height of your projector depends on the size of the projected image and the available space for it. Use caution when climbing a ladder, and consider removing the projector from its wall-mounting bracket to clean it. To focus and adjust the image Rotate the focus ring right or left until the image is in focus. The button illuminates to indicate the projector status see Determining projector status on page 56. Turn on the interactive projector. Right-click by touching and holding your finger to the surface for about two seconds.

Next